Rate Analysis of PCC : (Plain Cement Concrete)

100 to 150mm thick PCC only Labour: Rs.6.00/Sqft. Plum Concrete Only Labour: Rs.8.50-9.00/Cuft That is 300/Cum. Cement Bag: Rs.50- 60/Bag. Shuttering With Material: Rs.450-550/ Sqm. All above Rates is current market rate and analysis are considered as per Mix design report.

Density Of Cement Sand Aggregate & Steel

As mentioned earlier, the density of cement (OPC), which is the most common type of cement used in construction, is around 3.15 g/cm³ or 3,150 kg/m³. Sand is a commonly used construction material that is used as a fine aggregate in concrete and mortar. The density of sand can vary depending on its composition and moisture content but ...

What Is Plain Cement Concrete (PCC) In Construction?

PCC or Plain Cement Concrete is a mixture of cement, fine aggregate, and coarse aggregate. It is an essential component in the construction process and is used to create a flat and even surface before beginning R.C.C (Reinforced Cement Concrete) or masonry work. It acts as a barrier to prevent water from seeping into the soil and by …

How much cement sand & aggregate required …

M10 concrete ratio for 1 cubic meter is about 1 part cement: 3 parts sand: 6 parts aggregate (1:3:6) are made up of about 222kg (4.44bags of 50kg) cement, 710 kg sand, 1420kg aggregate and about 133 litres of water. …

Density Of Cement, Sand, And Aggregate

Contains 60 to 80 percent of the aggregate in concrete. Which produces compressive and bulk in concrete. The aggregates are classified into two categories as follows: Fine aggregate; Coarse aggregate; Fine aggregates usually consist of sand or crushed stone. Which is less than 4.75 mm in size. The coarse aggregate is usually …

Plain Cement Concrete (PCC)- Work Procedure

Work Method Opinion for Plain and Reinforced Cement Specific PCC and RCC. 2. Fine Aggregate. Fine aggregate will be of coarse sand consisting of hard, sharp and edgewise grains and shall pass through a screen starting 5 mm straight mesh. Sand shall be of standard specifications, wipe and free von dust, dirt and organic matter.

PCC Mix Design Fundamentals – Pavement Interactive

PCC consists of three basic ingredients: aggregate, water and portland cement. According to the Portland Cement Association (PCA, 1988 [1] ): "The objective in designing concrete mixtures is to determine the most economical and practical combination of readily available materials to produce a concrete that will satisfy the performance ...

Cement consumption in PCC 1:4:8 and M7.5

The PCC concrete ratio 1:4:8 indicates the proportions of cement, sand and aggregate used in the nominal concrete mix. The numbers indicate the parts of each material based on volumetric analysis. For example, in a 1:4:8 concrete mix ratio, 1 part of cement mixed to 4 parts sand and 8 parts of aggregate by volume.

Calculate Cement Sand & Aggregate from …

Method 1 involves using the recommended nominal concrete mix ratio to calculate the volume of each component. Method …

PCC Full Form in Civil Engineering : Ingredients, Preparation

The cement concrete in which no reinforcement is provided is called Plain Cement Concrete (PCC). It is simply a mixture of cement, sand, and aggregate containing a suitable proportion of water. It is sometimes called mass cement concrete or cement concrete. It is considerably stronger in compression but weak in tension and …

How To Calculate Cement, Sand & Aggregates Quantity in Concrete

Now we start calculation to find Cement, Sand and Aggregate quality in 1 cubic meter of concrete. CALCULATION FOR CEMENT QUANTITY; Cement= (1/5.5) x 1.54 = 0.28 m 3 ∴ 1 is a part of cement, 5.5 is sum of ratio Density of Cement is 1440/m 3 = 0.28 x 1440 = 403.2 kg We know each bag of cement is 50 kg

Calculation of Cement, Sand and Aggregate for M-10, M …

Calculation of Cement, Sand and Aggregate for M-10, M-15, M-20 and M-25 (Nominal mixes) concrete mix grades uses. cement sand aggregates in kgs cft ... Used for: Patio slabs, pathways,Pcc and non-structural work. Type: Domestic & commercial use. M 15. Used for: Pavement kerbs and floor blinding. Type: Domestic & Commercial. …

Application Description

Basic components of PCC include coarse aggregate (crushed stone or gravel), fine aggregate (usually natural sand), Portland cement, and water. The aggregate functions as a filler material, which is bound together by hardened Portland cement paste formed by chemical reactions (hydration) between the Portland cement …

PCC Concrete: Ratio, Grade & Full Form

This ratio is crucial in determining the strength and durability of the concrete. A higher PCC ratio results in stronger and more durable concrete, but it also increases the cost. PCC concrete mix ratio is 1:5:10, which means 1 part of cement, 5 parts of sand, and 10 parts of aggregate. PCC in construction is used to make a level bed for footing.

Rate analysis for PCC 1:4:8 (M7.5) – calculate quantity & cost

What Is Plain Cement Concrete Or PCC Concrete?

The density of Plain Cement Concrete (PCC) depends on its composition, specifically the ratio of cement, sand, and aggregate used. In General, the density of Plain Cement Concrete ranges from 2200 to 2500 kg/m³. The actual density of Plain Cement Concrete (PCC) depends on the specific materials used, the degree of compaction, and …

Cement Concrete Calculator | PCC Calculator | RCC …

Calculate cement concrete mix design or estimate how much cement concrete volume is required for your construction using our free online calculator. Know exactly how many …

PCC Volume Calculator | Free Estimate of Cement, Sand, Jelly

Plain Cement Concrete (PCC) is composed mixture of cement, aggregates, sand, water and chemical admixtures. Calculate portland cement concrete or PCC concrete mix …

Plain cement concrete (PCC)- Materials, …

The ratio of materials in PCC: The ratio of cement, sand, and brick chips in the foundation should be 1:3:6.But if it is applied in the car parking area, the ratio will be changed to 1:2:4. Properties of plain cement concrete. …

cement consumption in PCC 1:5:10 and M5

Ratio of water and cement is known as water cement ratio which is about 60 litre per bag cement for m5 grade of concrete. 1 bag cement required = 60 litre of water. 41.6 bags = 41.6×60= 2496 litre of water. So we have …

How much cement sand & aggregate required for M7.5 concrete

For 1 bag of cement = 1469/3.42 = 430 kgs aggregate. 225kg of sand and 430 kg aggregate are required per 50 kg bag of cement for m7.5 grade of concrete. Thus, You would need 225kg Sand and 403kg aggregate per 50kg bag of cement to make M7.5 concrete. How much cement sand & aggregate required for M7.5 concrete.

Cement Concrete Calculator | PCC Calculator | RCC …

Strength of PCC is defined as compressive strength after 28 days, expressed as M15, M20, where M stands for Mix and 15 stands for 15 N/mm 2 (n/mm 2 must be read as 'Newton's per millimeter Cubic') compressive strength at 28 days. The proportions of materials (cement, sand, coarse aggregate) for nominal mix/design mix concrete that are …

Cement Concrete Calculator: How much cement concrete …

Common mix ratios include 1:2:4 (cement:sand:aggregate) for general construction and 1:1.5:3 for reinforced structures. ... By accurately calculating the quantities of cement, sand, and water for PCC, you can ensure efficient material usage, avoid wastage, and achieve the desired strength and workability for your concrete base.

Calculating the quantity of cement, sand, & aggregates in M10 …

Practically for good workability, the water we add for the concrete is 133 liters. Alternate method: 1. Volume of cement ( from above) = 0.154 cum. 2. Volume of sand = [volume of cement × b] = [0.154 cum × 3] = 0.462 cum. 3. Volume of aggregates = [volume of cement × c]

Plain Cement Concrete: Components, Advantages

What is Plain Cement Concrete? Plain cement concrete called as simply "cement concrete (PCC)" or "binding concrete". The ratio for PCC concrete is 1:5:10, which represents 1 …

How much cement sand & aggregate required for M15 concrete

The mix proportion for M15 concrete is typically 1:2:4, where 1 is the ratio of cement, 2 is the ratio of sand, and 4 is the ratio of coarse aggregate. This means, for every 1 part of cement, you would need 2 parts of sand and 4 parts of coarse aggregate. The exact quantities would depend on the total volume of concrete you want to produce.

Plain cement concrete (PCC) | Application, …

PCC is a mixture of cement, sand, aggregate and water. It has a high compression strength but a low tension and shear strength. This concrete is also known as mass cement concrete or cement …

Calculate Quantities of Materials for Concrete -Cement, Sand, Aggregates

Thus, the quantity of cement required for 1 cubic meter of concrete = 0.98/0.1345 = 7.29 bags of cement. The quantities of materials for 1 m3 of concrete production can be calculated as follows: The weight of cement required = 7.29 x 50 = 364.5 kg. Weight of fine aggregate (sand) = 1.5 x 364.5 = 546.75 kg.

Plain Cement Concrete: Components, Advantages

The ratio for PCC concrete is 1:5:10, which represents 1 part cement, 5 parts sand, and 10 parts aggregate. To make a level bed for the foundation, PCC is used. Proportioning Plain Cement Concrete: Based on the specification or necessity, the proportioning is carried out. It is often a 1:2:4 or 1:3:6 blend.

Aggregate – Pavement Interactive

Aggregate" is a collective term for the mineral materials such as sand, gravel and crushed stone that are used with a binding medium (such as water, bitumen, portland cement, lime, etc.) to form compound materials (such as asphalt concrete and portland cement concrete). By volume, aggregate generally accounts for 92 to 96 percent of HMA and ...

Calculate Quantities of Materials for Concrete -Cement, …

Weight of fine aggregate (sand) = 1.5 x 364.5 = 546.75 kg. Weight of coarse aggregate = 3 x 364.5 = 1093.5 kg. Concrete Calculator: Calculate Quantities of Materials for …

What Is PCC Concrete? | PCC Concrete Mix Ratio

The sand used for PCC concrete should be in accordance with the standard specifications. The sand used for PCC Concrete should be free from dust, dirt, and organic matter. Also, sea sand should not be …

Cement Concrete Calculator: How much cement concrete do …

Length. Width. Depth. Grade of concrete. Result: Total volume of cement concrete: M3. Or. Cubic feet. Cement Concrete Calculation. Using this calculator you can calculate how …

Density of Cement Sand and Aggregate

The cement mixed with fine aggregate produces mortar for masonry, or with sand and gravel, produces concrete. First, density is the ratio of mass to volume. So it can be indicated in terms of kg / m 3, which is 1440kg / m 3 for cement. ... PCC (Plain Cement Concrete) 2400: 24: Pitch: 1010: 10.1:

Size of aggregate used in RCC, PCC, slab, Road, Bridge & Dams

2. PCC (Plain Cement Concrete): Coarse aggregates with sizes ranging from 40mm to 20mm are commonly used in PCC. 3. Slab Construction: For slabs, 20mm aggregates are commonly used.This size provides a good balance of workability and strength. 4. Road Construction: Aggregates used in road construction can vary, but commonly 20mm and …

Concrete Calculator

Ans. Materials required are 7 nos. of 50 kg bag of cement, 0.42 m 3 of sand and 0.83 m 3 of stone aggregate. This is a free online tool by EverydayCalculation to calculate …

Plain Cement Concrete or PCC: Advantages and Uses

Plain Cement Concrete (PCC), commonly known as cement concrete, is a fundamental construction material composed of a precise mixture of cement, fine aggregates (usually sand), coarse aggregates (typically gravel or crushed stone), and water. It is used extensively in construction for creating sturdy foundations, base layers, and durable …